Log in Favourites Cart
custom cover 1 design with ai
custom cover 2 design it yourself
custom cover 3 instant price
Custom size drain cover order3D
Drag to turn it
Custom size drain cover order: a drawing with its sizes
Click to enlarge

Custom size drain cover order

From$34.74$28.95 ex VAT

Any drain cover or grating, made to the size and shape you need. You design it here on the page, see it in 3D in the finish you want and get the price straight away. Then we laser cut it from solid steel plate in our Millom workshop and send it to you.

Read full description3 questions answered

Design it yourself online, in a couple of minutes

Our designer draws your cover as you go, shows it in 3D in the finish you choose, and prices it there and then. No drawings to send and no waiting for a quote.

  1. Shape and sizeRound, square, rectangle, or draw your own, to the millimetre.
  2. Holes and cut-outsScrew holes and downpipe cut-outs exactly where you need them, even open to the edge.
  3. See it and orderIn 3D with its price, then laser cut to order for you.
Have a design code?
Finish: Black powder coat
Thickness: 6mm

    Everything else stays as it is, and you can check the new drawing before it goes in your cart.

    Design with AI

    Take a photo of the drain or recess with a tape measure across it, upload a sketch with its sizes, or just describe it. We will draw it in seconds and show it to you in 3D.

    Design priority
    Small openings keep out leaves and are kinder to heels and paws. Strong has wider steel between straight slots or holes.

    Your photo and words go to Claude, an AI from Anthropic, to draw it. We keep the photo in case of any question about the fit, until 6 months after your order is sent, or 90 days if you do not order. Up to 100 a day.

    Design your drain cover

    1Shape

    0 for sharp corners.

    Click on the grid to place each corner, then click the first corner to close the shape. Drag a corner to move it.

    2Screw holes and cut-outs

      3Pattern

      Our standard round design: rings of slots with bars across them, sized to your cover. Slots keep clear of any screw holes and cut-outs.

      Plain steel, with only your screw holes and cut-outs.

      Slots at the angle you choose: 45 is the usual diagonal, 0 runs straight across and 90 straight up.Straight slots run across the shortest width, for the most strength.Round holes in rows across the cover, like perforated plate.Round holes round circles from the middle of the cover, working in from the outside.

      Long slots are split by cross bars so the steel does not warp as it is cut: no slot is more than 30 times as long as it is wide. More cross bars make a big cover stronger.

      Angled slots longer than the cover is wide are linked across the middle, as on our stock gully grids.

      The border also goes round every screw hole and cut-out, so the pattern keeps clear of them.

      Product description

      Any drain cover or grating, made to the size and shape you need. You design it here on the page, see it in 3D in the finish you want and get the price straight away. Then we laser cut it from solid steel plate in our Millom workshop and send it to you.

      Two ways to design it

      Design with AI. Take a photo of the drain or recess with a tape measure across it, or of a sketch with the sizes written on it, or just describe what you need. Our AI draws a first go in a few seconds. If it has had to assume something, it asks you, and your answer updates the design.

      Design it yourself. Choose round, square or rectangle and type in the sizes, or draw your own shape on the grid. Put screw holes and cut-outs exactly where you need them, then choose the pattern. You can work in millimetres or inches.

      Either way, you can change anything in the designer before you order.

      What you can make

      • Any size from 50mm across up to 2400 × 1200mm.
      • Any shape: round, square, rectangle, or your own outline with up to 60 corners, such as an L shape or a cut-off corner. Corners can be sharp or rounded to any radius.
      • Screw holes and cut-outs: up to 40 on one cover. Screw holes from 3 to 50mm, and round or square cut-outs from 20 to 600mm. A cut-out can run out to the edge, so the cover slides on round a pipe.
      • Four patterns: diagonal slots, straight slots, round holes like perforated plate, or our rings pattern for round covers. You choose the slot or hole size, the steel between them and the plain border round the edge. The border goes round every hole and cut-out too.

      Measuring up

      1. Measure the opening the cover sits in, both ways and in two or three places. Openings are rarely perfectly square, so use the smallest.
      2. Take 2mm off each way, so the cover drops in with about 1mm clear all round. A 302mm opening gets a 300mm cover.
      3. Pipes and holes: make a cut-out 2mm bigger than the pipe it goes round, so a 68mm downpipe gets a 70mm cut-out. Screw holes and cut-outs are placed by their centre, measured from the bottom left corner.

      If the opposite sides of the opening are different lengths, as concrete often is, draw your own shape with the lengths you measured. The AI will do this for you from your sizes or a photo.

      Check it, then order

      The price updates as you design, in the finish and thickness you choose, so there is no waiting for a quote. Before it goes in your basket you get a full drawing of your cover, with every size, hole and cut-out on it, to check and approve. It is cut to exactly that drawing, and the drawing is kept with your order.

      We also show an estimate of the load your cover will take, worked out the way BS EN 124 tests a cover. It is a guide to help you choose the thickness and pattern, not a certified rating.

      How we make them

      Every one of our drain covers is cut and finished in our own workshop in Millom, Cumbria, on the edge of the Lake District. In fact, the very first thing we ever made was a drain cover. We couldn't buy one in the size we needed, so we cut our own, and we've not looked back since.

      Laser cut from solid steel plate

      Our covers are cut on our 6kW fibre laser, for a precise, clean cut every time.

      Finished by hand

      Once cut, every cover is checked over and its edges are ground smooth, ready for finishing.

      Weathering steel covers are left bare and packed up as they are. Once they're installed outside, they form their own protective oxide layer, a rich rust-brown finish that protects the steel underneath.

      Powder coated covers go into our oven three times:

      1. First on their own, extra hot, to burn off any oil or grease left on the surface.
      2. Then with a corrosion-protecting primer, which is cured in the oven.
      3. Finally with the powder top coat, cured once more.

      [Photo: the laser. Caption: Our fibre laser in the Millom workshop]

      Then they're packed up and sent out to you, straight from Millom, ready to look the part wherever you need them.

      Frequently asked questions

      What size drain cover do I need?

      If you’re replacing an existing cover, measure the old one and choose a new cover the same size. If we don’t stock that exact size, a cover a few mm smaller will usually still fit.

      If you’re measuring the recess the cover sits in, rather than the cover itself, choose a cover a few mm smaller than the recess so it drops in easily.

      Measure in millimetres, across the top: corner to corner along each side for a square cover, and straight across the middle for a round one. Measure in two or three places in case it isn’t quite square or round, and go by the smallest figure.

      What finish should I choose?

      We make drain covers in two finishes: powder coated steel and weathering steel.

      The powder coated covers have a corrosion-inhibiting primer under a powder top coat. They’re ideal for the edges of paths, around the house, patios and similar spots.

      For driveways and areas with heavy foot traffic, we’d suggest our weathering steel covers, which are built to last.

      What thickness should I choose?

      Our powder coated covers usually come in one thickness, which suits paths, patios and other out-of-the-way spots.

      Our weathering steel covers are made for busier paths and driveways, so some sizes come in more than one thickness. For a path, the thinner option is usually fine. For a driveway, choose the thickest option, and check the listing’s “Suitable for” says driveways. Some of the larger sizes are for paths and patios only.

      Still have a question? Ask us