185mm (~7.3") square drain cover gully grid
SKU:
185mm square drain cover gully grid, laser cut from structural steel and then powder coated with corrosion protection primer and matt black top coat.
Product description
A flat black square grid with bold diagonal slots cut through it, this 185mm gully cover keeps leaves and larger debris out of the drain while letting water run straight through. The slots run in long parallel lines at a steady angle, with a few shorter ones towards the corners, so it looks tidy and deliberate rather than plain. The matt black finish sits quietly against paving, concrete or tarmac.
It's laser cut from S275 structural steel, 8mm thick, so it has a solid feel and weighs around 1.44kg. The finish is a powder coat in two stages: a corrosion protection primer, then a matt black top coat. That makes it suitable for outdoor use, whether it sits by a back door, in a yard or on a driveway. The edges are neatly cut and the corners are slightly rounded.
If you're replacing an old or broken grid, measure your gully opening before you order, as the cover is a flat square plate.
- Size: 185mm x 185mm (7.3 x 7.3 inches)
- Thickness: 8mm (0.31 inches)
- Material: S275 structural steel
- Finish: corrosion protection primer with matt black powder coat
- Weight: 1.44kg
- Made in the UK
Features
| Main theme | Drain covers & Gully grids |
|---|---|
| Shape | Square |
| Surface finish | Black powder coat |
| Width (mm) | 185 mm |
| Height (mm) | 185 mm |
| Width (inches) | 7.3 inches |
| Height (inches) | 7.3 inches |
| Material | S275 Structural steel |
| Weight (Kg) | 1.44 Kg |
| Suitable for outdoors | Yes |
| Thickness (mm) | 8 mm |
| Thickness (inches) | 0.31 inches |
| Suitable for | Out of the way areas, downpipes, patios and pavement edges |
How we make them
Every one of our drain covers is cut and finished in our own workshop in Millom, Cumbria, on the edge of the Lake District. In fact, the very first thing we ever made was a drain cover. We couldn't buy one in the size we needed, so we cut our own, and we've not looked back since.
Laser cut from solid steel plate
Our covers are cut on our 6kW fibre laser, for a precise, clean cut every time.
Finished by hand
Once cut, every cover is checked over and its edges are ground smooth, ready for finishing.
Weathering steel covers are left bare and packed up as they are. Once they're installed outside, they form their own protective oxide layer, a rich rust-brown finish that protects the steel underneath.
Powder coated covers go into our oven three times:
- First on their own, extra hot, to burn off any oil or grease left on the surface.
- Then with a corrosion-protecting primer, which is cured in the oven.
- Finally with the powder top coat, cured once more.
[Photo: the laser. Caption: Our fibre laser in the Millom workshop]
Then they're packed up and sent out to you, straight from Millom, ready to look the part wherever you need them.
Frequently asked questions
What size drain cover do I need?
If you’re replacing an existing cover, measure the old one and choose a new cover the same size. If we don’t stock that exact size, a cover a few mm smaller will usually still fit.
If you’re measuring the recess the cover sits in, rather than the cover itself, choose a cover a few mm smaller than the recess so it drops in easily.
Measure in millimetres, across the top: corner to corner along each side for a square cover, and straight across the middle for a round one. Measure in two or three places in case it isn’t quite square or round, and go by the smallest figure.
What finish should I choose?
We make drain covers in two finishes: powder coated steel and weathering steel.
The powder coated covers have a corrosion-inhibiting primer under a powder top coat. They’re ideal for the edges of paths, around the house, patios and similar spots.
For driveways and areas with heavy foot traffic, we’d suggest our weathering steel covers, which are built to last.
What thickness should I choose?
Our powder coated covers usually come in one thickness, which suits paths, patios and other out-of-the-way spots.
Our weathering steel covers are made for busier paths and driveways, so some sizes come in more than one thickness. For a path, the thinner option is usually fine. For a driveway, choose the thickest option, and check the listing’s “Suitable for” says driveways. Some of the larger sizes are for paths and patios only.
Still have a question? Ask us

